MUTOH SC-650 User's Guide Page 49
- Page / 108
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
User’s Guide SC-PRO Cutting Plotter
CHAPTER 4 : WALKTHROUGH THE OPERATION PANEL
49
AP-75280 – Rev. 1.2
4.2.4 Pre-Feed length
This parameter is directly related to the loading of ROLL FRONT / ROLL media. The Pre-Feed length or
SHUFFLE length has to be set before a roll is loaded.
There are three reasons for using a Pre-Feed Length:
1.
The length of media set for the Pre-Feed length parameter will be pulled off the roll, before the cutting
job starts. This will prevent media from being pulled off the roll at high speed and acceleration. High
speed can only be properly used on condition that the media can move freely, without having to be
pulled off the roll during a job.
2.
Before actually cutting starts the complete length of the media is shuffled back and forth through the
cutter, ensuring that the pressure rollers have a discrete path while the user has the time to verify if
the vinyl transport goes well.
3.
Your SC-Pro cutter has been equipped with MUTOH’s unique AUTO-SHEET-OFF feature, to
automatically cut off media at the end of a cutting sequence. Following an automatic PAGE command
or a manual PAGE command initiated via the control panel, the cutter will shuffle through the pre-set
Pre-Feed length of media, to ensure that there is enough media left for a possible replot. If there is
not enough media left, the cutter will stop before the end of the assigned media length and switches to
SHEET mode. The cutter will not initiate the media again in between two contour cutting jobs.
Pre- Feed Length
1000
[mm]
Save: Exit:
Pre-Feed Length 0 – 1000 - 10000 [mm]
The media will be fed 1 meter before the cutting job will start.
Notes
• Please note that the use of the PRE-FEED LENGTH should not be regarded as a loss of time. If the
shuffle movement is executed without difficulty, the user can be convinced that the sign to be cut will be
executed with very little risk of media tracking problems. As such, it will result in a time-saving
operation, preventing that the user will have to re-cut a very complex design because of bad media
alignment.
Notes
•
Please note that the cutting range is not limited by the Pre-Feed Length which you have set. In case a
design, which exceeds the shuffle length, is sent to the cutting plotter, the cutter will react as follows:
o The first vector, which exceeds the limit, will be cut using reduced speed for the distance exceeding
the limit.
o The cutter will continue at the requested speed until the new limit is exceeded.
o However, this should not be a reason for you not to change the pre-feed length at all, as by omitting
to change it; you will be inhibited to check the full vinyl transport before the job is launched
o When there is an end of roll detection during the pre-feed, the cutter will automatically switch to
SHEET mode.
- User’s Guide 1
- COPYRIGHT NOTICE 3
- TABLE OF CONTENTS 7
- AP-75280 – Rev. 1.2 10
- 1 REGULARISATION AND SAFETY 11
- INFORMATION 11
- DO NOT STARE INTO BEAM 12
- CLASS 2 LASER PRODUCT 12
- LASER RADIATION 12
- ► Cutting head 13
- ► Grid rollers 13
- 2305 1062 15
- Room conditions 16
- 2.3 PART NAMES AND FUNCTIONS 17
- 2.3.2 Rear of the SC-PRO 18
- 2.3.3 Operation panel 19
- 2.4 IN-THE-BOX CONTENTS 20
- 3 BASICS 21
- 3.1.2 Replace cutter blade 22
- CHAPTER 3 : BASICS 23
- TYPE 1 TYPE 2 25
- REAR FRONT 25
- 3.2.1 Handling media 26
- 3.3 LOADING MEDIA 27
- 3.3.2 Loading sheet media 33
- 4 WALKTHROUGH THE OPERATION 35
- 4.1.1 SHEET OFF key 36
- 4.1.2 ORIGIN key 37
- 4.1.3 TEST key 37
- 4.1.4 CONTOUR CUTTING key 38
- 4.1.5 SPEED key 41
- 4.1.6 FORCE key 42
- 4.1.7 OFFSET key 43
- 4.1.8 TOOL key 44
- 4.2 MENU OVERVIEW 45
- 4.2.1 Sheet off mode 48
- 4.2.2 Sheet off margin 48
- 4.2.3 Auto Shuffle 48
- 4.2.4 Pre-Feed length 49
- 4.2.5 Max Sheet length 50
- 4.2.6 Page mode 51
- 4.2.7 Origin 52
- 4.2.8 Laser speed 52
- 4.2.9 Tool-up speed 53
- 4.2.10 Job focus 53
- 4.2.11 Smoothing 53
- 4.2.14 Language 55
- 4.2.15 Emulation 55
- 4.2.16 Program step 55
- 4.2.17 VS/ZF/AS 56
- 4.2.18 ToolSwap Detect 56
- 4.2.19 LCD contrast 56
- 4.2.20 Keyboard beep 57
- 4.2.21 Versions 57
- 4.2.22 Basic / Full menu 57
- 4.2.23 Serial communication 58
- 4.3 SPECIAL KEY COMBINATIONS 60
- 4.3.2 EPOS laser OFF 61
- 4.3.3 Bar code verification 61
- 4.3.4 Updating the keyboard 62
- 4.3.5 Reset the keyboard 62
- 4.3.7 Factory default 63
- 4.4.1 While cutting 64
- ► The knife depth 65
- ► The cutting pressure 65
- ► The offset 65
- 5.1 KNIFE DEPTH 66
- - 0,05 mm 68
- + 0,05 mm 68
- - 0,01 mm 68
- + 0,01 mm 68
- 5.2 SETTING THE TOOL FORCE 69
- 5.3 OFFSET PRINCIPLE 69
- 5.4 EPOS TEST CUTS 70
- 5.4.2 EPOS readout 72
- 5.4.3 EPOS calibration 73
- 5.5 CUT THROUGH TEST 76
- 5.6 XY-DISTANCE ACCURACY 78
- 6 CONTOUR CUTTING 79
- CHAPTER 6 : CONTOURCUTTING 80
- 6.3 SQUARE DETAILS 81
- 6.4 CUT AREA MEASUREMENT 85
- 7 MAINTENANCE 87
- CHAPTER 7 : MAINTENANCE 88
- 8 TROUBLESHOOTING 89
- 8.2 ERROR MESSAGES 92
- CHAPTER 8: TROUBLESHOOTING 100
- ► One cutting knife blade 105
- CHAPTER 9 : CONSUMABLES 106
- 107
Related products and manuals for Power universal cutters MUTOH SC-650
(97 pages)© 2020, manymanuals.com. All rights reserved. | 0.810 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals