MUTOH SC-650 User's Guide download pdf (Page 21)

User’s Guide SC-PRO Cutting Plotter

CHAPTER 3 : BASICS

AP-75280 – Rev. 1.2

3 BASICS

3.1 INSTALLING AND REPLACING TOOLS

3.1.1 Installing tools

At the right-hand side of the cutter head, you will find a pivoting mounting bracket. Opening this bracket will

enable you to install a full range of cutting and drawing tools.

To do so, please follow the instructions mentioned below.

Step 1 : Open the screw (1) to unlock the tool head-mounting bracket.

Step 2 : Hold back the clip (2) of the tool head and slide the tool into position, making sure the tool collar

fits into the groove just beneath the locking screw (3).

Step 3 : Fasten the screw to secure the tool into position.

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 107 108

User’s Guide 1
COPYRIGHT NOTICE 3
TABLE OF CONTENTS 7
AP-75280 – Rev. 1.2 10
1 REGULARISATION AND SAFETY 11
INFORMATION 11
DO NOT STARE INTO BEAM 12
CLASS 2 LASER PRODUCT 12
LASER RADIATION 12
► Cutting head 13
► Grid rollers 13
2305 1062 15
Room conditions 16
2.3 PART NAMES AND FUNCTIONS 17
2.3.2 Rear of the SC-PRO 18
2.3.3 Operation panel 19
2.4 IN-THE-BOX CONTENTS 20
3 BASICS 21
3.1.2 Replace cutter blade 22
CHAPTER 3 : BASICS 23
TYPE 1 TYPE 2 25
REAR FRONT 25
3.2.1 Handling media 26
3.3 LOADING MEDIA 27
3.3.2 Loading sheet media 33
4 WALKTHROUGH THE OPERATION 35
4.1.1 SHEET OFF key 36
4.1.2 ORIGIN key 37
4.1.3 TEST key 37
4.1.4 CONTOUR CUTTING key 38
4.1.5 SPEED key 41
4.1.6 FORCE key 42
4.1.7 OFFSET key 43
4.1.8 TOOL key 44
4.2 MENU OVERVIEW 45
4.2.1 Sheet off mode 48
4.2.2 Sheet off margin 48
4.2.3 Auto Shuffle 48
4.2.4 Pre-Feed length 49
4.2.5 Max Sheet length 50
4.2.6 Page mode 51
4.2.7 Origin 52
4.2.8 Laser speed 52
4.2.9 Tool-up speed 53
4.2.10 Job focus 53
4.2.11 Smoothing 53
4.2.14 Language 55
4.2.15 Emulation 55
4.2.16 Program step 55
4.2.17 VS/ZF/AS 56
4.2.18 ToolSwap Detect 56
4.2.19 LCD contrast 56
4.2.20 Keyboard beep 57
4.2.21 Versions 57
4.2.22 Basic / Full menu 57
4.2.23 Serial communication 58
4.3 SPECIAL KEY COMBINATIONS 60
4.3.2 EPOS laser OFF 61
4.3.3 Bar code verification 61
4.3.4 Updating the keyboard 62
4.3.5 Reset the keyboard 62
4.3.7 Factory default 63
4.4.1 While cutting 64
► The knife depth 65
► The cutting pressure 65
► The offset 65
5.1 KNIFE DEPTH 66
- 0,05 mm 68
+ 0,05 mm 68
- 0,01 mm 68
+ 0,01 mm 68
5.2 SETTING THE TOOL FORCE 69
5.3 OFFSET PRINCIPLE 69
5.4 EPOS TEST CUTS 70
5.4.2 EPOS readout 72
5.4.3 EPOS calibration 73
5.5 CUT THROUGH TEST 76
5.6 XY-DISTANCE ACCURACY 78
6 CONTOUR CUTTING 79
CHAPTER 6 : CONTOURCUTTING 80
6.3 SQUARE DETAILS 81
6.4 CUT AREA MEASUREMENT 85
7 MAINTENANCE 87
CHAPTER 7 : MAINTENANCE 88
8 TROUBLESHOOTING 89
8.2 ERROR MESSAGES 92
CHAPTER 8: TROUBLESHOOTING 100
► One cutting knife blade 105
CHAPTER 9 : CONSUMABLES 106
107

Comments to this Manuals

No comments

MUTOH SC-650 User's Guide Page 21

Comments to this Manuals

Related products and manuals for Power universal cutters MUTOH SC-650